This standard is issued under the fixed designation A/AM; the number 1 This practice is under the jurisdiction of ASTM Committee A01 on Steel. 22 Oct ASTM A – 4CTb Designation: A /A M – 01” An American National Standard Standard Pra. 1 Jan Buy ASTM A /AM: PRACTICE FOR STEEL CASTINGS, WELDING, QUALIFICATIONS OF PROCEDURES AND PERSONNEL.
|Published (Last):||5 June 2014|
|PDF File Size:||11.29 Mb|
|ePub File Size:||2.75 Mb|
|Price:||Free* [*Free Regsitration Required]|
The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or asttm to date.
You may delete a document from your Alert Profile at any time.
P-number designations in the ASME grouping of base metals for qualification astn be different than the category numbers listed in Table 1. Combining values from the two systems may result in nonconformance with the standard. Add to Alert PDF.
Combining values from the two systems may result in nonconformance with this practice. Link to Active This link will always route to the current Active version of the standard.
The orientation of the welds with respect to the horizontal and vertical planes of reference is classified into four positions, namely, flat, horizontal, vertical, and overhead. ICS Number Code Changes other than those listed may be made without requalification, provided the procedure is revised to show these changes. We have no amendments or corrections for this standard.
It is informational only and not an official part of the standard; the full text of the standard itself must be x488 to for its use and application. Need more than one copy? Standards Subsctiption may be the perfect solution. Link to Active This link will always route to the current Active version of asgm standard. Please first log in with a verified email before subscribing to alerts.
Guided bend test specimens shall be prepared by cutting the test plate or pipe to form specimens of approximately rectangular cross section. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior a48 use.
The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. If the document is revised or amended, you will be notified by email. Work Item s – asfm revisions of this standard. Your Alert Profile lists the documents that will be monitored.
This standard is not included in any packages. This abstract is a brief summary of the referenced standard. A welding procedure must be set up as a new procedure and must be requalified when any of the changes in essential variables, inclusive, are made. The welder or operator successfully performing the procedure qualification test is automatically qualified for performance. Four types of test shall be conducted in the qualification procedures such as tension test, bend test, Charpy impact test and radiographic test.
Please first verify your email before subscribing to alerts. The materials are categorized as carbon steel, carbon and carbon-manganese steel, low alloy steel, ferritic stainless steel, martensitic stainless steel, low carbon austenitic stainless steel, unstabilized austenitic stainless steel, austenitic stainless steel, duplex austenitic-ferritic stainless steel, precipitation-hardened austenitic stainless steel, nickel base alloy, steel castings, austenitic manganese.
Referenced Documents purchase separately The z488 listed below are referenced within the subject standard but are not provided as part of the standard. Guided bend test specimens are of three types depending on which surface aetm bend, face bend, or root bend is on the convex outer side of the bent specimen.
Within the text, the SI units are shown in brackets. Work Item s – proposed revisions of this standard. This standard is also available to be included in Standards Subscriptions.
The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. As the voice of the U. P-number designations in the ASME grouping of base metals for qualification may be different than the category numbers listed in Table 1.
Standard Practice for Steel Castings, Welding, Qualifications of Procedures and Personnel
Active view current version of standard. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Historical Version s – view previous versions of standard.
This practice covers the qualification of procedures, welders, and operators for the fabrication and repair of steel castings by electric arc welding. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.
Already Subscribed to this document. You can download and open this file to your own computer but DRM prevents opening this file on another computer, including a networked server. Active view current version of standard Translated Standard: All welders and operators welding castings under this practice shall pass the welder qualification test. Proceed to Checkout Continue Shopping.