DIN EN 20898 1 PDF

The European Standard EN has the status of a . ISO (upon which BS EN is based), altering clause 1. Standard [WITHDRAWN] DIN EN Mechanical properties of fasteners; bolts, screws and studs (ISO ); german version EN. Purchase your copy of BS EN , ISO as a PDF download or hard copy directly from the official BSI Shop. All BSI British.

Author: Tojakasa Tulabar
Country: Martinique
Language: English (Spanish)
Genre: Science
Published (Last): 19 November 2015
Pages: 318
PDF File Size: 6.27 Mb
ePub File Size: 7.49 Mb
ISBN: 317-2-51622-468-6
Downloads: 56963
Price: Free* [*Free Regsitration Required]
Uploader: Tarisar

Vis et goujons und legiertem Stahl — Teil 1: Figure 12 — Alternative left-hand thread marking 9. By using this site, you agree to the Terms of Use eh Privacy Policy. Users of British Standards should make sure that they possess the latest amendments or editions. Torsional test and minimum torques for bolts and screws with nominal diameters 1 mm to 10 mm?

Figure 2 — Application of proof load cin full-size bolts and screws 8. Set screws and similar threaded fasteners not 208988 tensile stresses; — Part 6: Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, the EN ISO title page, page 2, the ISO title page, pages ii to iv, pages 1 to 24 and a back cover.

The work of preparing International Standards is normally carried out through ISO technical committees.

The maximum value for G and the formulae for the minimum eh for E are specified in Table 3. The application of this standard is restricted to bolts and screws of property class 5.

Surface hardness readings taken at HV 0,3 shall be compared with a similar core hardness reading at HV 0,3 in order to make a realistic comparison and determine the relative increase which is permissible up to 30 Vickers points. The test applies to bolts and screws with nominal thread diameters d u 3 mm as well as to short bolts and screws with nominal thread diameters 3 mm u d u 10 mm which cannot be subjected to a tensile test.

  UNEXPECTED RETURNS ED EASTERLING PDF

BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Torsional test and minimum torques for bolts and screws with nominal diameter from 1 mm to 10 mm. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service.

Screws & Bolts – Mechanical Properties

For the purposes of this part of ISO a distributor marking fasteners with his unique identification mark shall be considered a manufacturer. The grips of the testing machine should be self-aligning to avoid side thrust on the test piece.

Copyright Copyright subsists in all BSI publications. Screws threaded to the head shall pass the requirement of this test if a fracture which causes failure originates in the free length of thread, even if it has extended or spread into the fillet area or the head before separation. These values if received from tests of full size bolts and screws will vary because of processing method and size effects.

Mechanical properties of fasteners made of carbon dni and alloysteel— Part 1: For all property classes, if the maximum hardness is exceeded, a retest shall be conducted at the mid-radius position, one diameter back from the end, at which position the maximum hardness specified shall not be exceeded. It is carried out for the purpose of determining the tensile strength. A British Standard does not purport to include all the necessary provisions of a contract.

Except as permitted under the Copyright, Designs and Patents Act no extract may be reproduced, stored in a retrieval system or transmitted in any form or 2088 any means — electronic, photocopying, recording or otherwise — without prior written permission from BSI.

  A MENINA DO MAR DE SOPHIA DE MELLO BREYNER PDF

Mechanical Properties – Steel Screws and Bolts ISO 898-1 EN 20898-1

Table 14 — Marking symbols Property class 3. In order to meet the requirements of this test, the fracture shall occur in the shank or the free threaded length of the bolt and not at the junction of the head and the shank. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by Februaryand conflicting national standards shall 2898 withdrawn at the latest by February Torsional test and minimum torques for bolts and screws with nominal diameters 1 mm to 10 mm.

Draft International Standards adopted enn the technical committees are circulated to the member bodies for voting. Figure 10 — Marking of rn The symbols in Table 16 are permissible as an alternative identification of property classes. Values for E are given in Table If the microscope is of a type with a ground glass screen, the extent of decarburization can be measured directly with a scale.

With exception to part 7, which defines test standards, the parts of this standard define properties for fasteners made of carbon steel and alloy steel.

Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services.

Author: admin