ASTM E384 – 11E1 PDF

This standard is issued under the fixed designation E; the number immediately This test method is under the jurisdiction of ASTM Committee E04 on. ASTM Ee1. August Standard Test Method for Knoop and Vickers Hardness of Materials. Historical Version. Status: Alert Withdrawn. Norwegian title: Standard Test Method for Knoop and Vickers Hardness of Materials. English title: Standard Test Method for Knoop and .

Author: Mojas Zucage
Country: Barbados
Language: English (Spanish)
Genre: Photos
Published (Last): 18 August 2006
Pages: 263
PDF File Size: 11.2 Mb
ePub File Size: 16.67 Mb
ISBN: 845-2-20954-347-3
Downloads: 93287
Price: Free* [*Free Regsitration Required]
Uploader: Gardagal

Astm e 11e1 pdf.

Referenced Documents purchase separately The documents listed below astm e — 11e1 referenced within the subject standard but are not provided as part of the standard. No other units of measurement are included in this standard. Click here to download full list of books.

Current edition approved Aug. The Knoop indenter does not produce a geometrically similar indentation as a function of test force. FORMAT Single User Subscription Site License Subscription BOOKS All Books PACKAGES All Packages EDITION to PUBLISHER.

Astm e — xstm pdf To determine these differences requires a very small physical indentation. This standard is issued under the fixed designation E; the number immediately following the designation indicates the year of original adoption or, in the case of revision, the year of last revision. Referenced Documents purchase separately The aatm listed below are referenced within the subject standard but are not asgm as part of the standard.

  KIRTAN SOHILA ENGLISH TRANSLATION PDF

ASTM E – 11e1 Standard Test Method for Knoop and Vickers Hardness of Materials

These variations may be intentional, axtm as produced by localized surface hardening, for example, from shot blasting, cold drawing, flame hardening, induction hardening, etc. Low test forces also extend hardness testing to materials too thin or too small for macroindentation tests.

NOTE 2—While Committee E04 is primarily concerned with metals, the test procedures described are applicable to other materials. This standard has been approved for use by agencies of the Department of Defense. NOK 1 ,00 excl. If you need to be able to add standards to the monitoring service, you must register as a user with your own username and password.

Referenced Documents purchase separately The documents listed below are referenced e834 the subject standard but are not provided as part of the standard. Significance and Use 4. Note 2—While Committee E04 is primarily concerned with metals, the test procedures described are applicable to other materials. Because of the large difference between the long and short Knoop asttm, the Knoop indenter is often better suited for determining variations of hardness over very small zstm compared to the Vickers indenter.

A number in parentheses indicates the year of last reapproval. If the s384 is revised or amended, you will be notified by email. The Vickers indenter usually produces a geometrically similar indentation at all test forces. Webprint Printed and bound. Add to Alert 3e84.

  JIS B 0401 PDF

However, because of the historical precedent and continued common usage, force values in gf and kgf units are provided for information e1 much of the discussion in this standard as well as the method of astm e — 11e1 the test results refers to atsm units. There were no books found for the applied search filters. The success of the specimen preparation procedure in 1e11 preparation-induced damage can, and will, influence test results; this problem becomes more critical as the test force decreases.

Ideally, the long diagonal is 7.

ASTM E384:11e1

Recommendations for low force microindentation testing can be found f Appendix X5. Medias this blog was made to help people to easily download or read PDF files. The two diagonals of a Knoop indentation are markedly different. This standard is also available to be included in Standards Subscriptions.

If the test is being conducted to meet 11s1 specified bulk hardness value, such as HRC, then most such tests will be conducted with Knoop at a gf load. Need more than one copy? Historical Version s – view previous versions of standard.

Author: admin